Brush Cutter Ignition Coil

Brush Cutter Ignition Coil

SKU: 0208050
Module Type: Solid-state CDI magneto armature
Core & Winding: Laminated electrical silicon steel with vacuum-poured epoxy insulation
Engine Matching: 40-5, 44-5, CG430, CG520, 1E40F-5, 1E44F-5 (43cc and 52cc 2-stroke platforms)
Commercial Terms: Brand: SeaSummer | Delivery Time: 30 Days | Packaging: Cardboard packaging
Send Inquiry
Add To Inquiry
Description

Jiaxing Norsun Trading Co., Ltd. is one of the leading manufacturers and suppliers of brush cutter ignition coil in China. With abundant experience, we are committed to providing high quality customized products with low price. Welcome to wholesale bulk CE approved products in stock here and get quotation from our factory.

 

Product Overview & Operating Details

Brush Cutter Electronic CDI Ignition Coil Assembly

Solid-State Magneto Armature for 43cc and 52cc 2-Stroke Power Equipment

 
 
product-1024-1024

Mechanical Construction and Ignition Operation

On small two-stroke utility engines, ignition timing and spark energy rely entirely on the mechanical interaction between the flywheel's embedded magnets and the stationary ignition module. As the flywheel spins past the silicon steel pole shoes, changing magnetic flux induces a low-voltage charge in the primary winding. The internal CDI timing circuit triggers at peak induction, discharging the stored current through the secondary step-up winding to generate the high-voltage pulse needed across the spark plug gap.

Because commercial brush cutters run between 7,500 and 9,500 RPM for hours at a time, vibration and engine block heat are the main causes of coil failure. Over time, heat cycles break down cheap internal lacquer insulation, leading to a weak spark or sudden engine cutouts once the cylinder reaches operating temperature.

To prevent internal shorting and wire fatigue, this module is cast in solid, heat-dissipating epoxy resin under vacuum. The solid block locks both primary and secondary windings in place, sealing out chain grease, two-stroke oil mist, grass debris, and rain.

The high-tension spark plug lead is jacketed in heavy-duty silicone to stop voltage from jumping to the bare aluminum cooling fins. Inside the 90-degree rubber plug boot, a phosphor bronze spring clip snaps firmly over the spark plug terminal so it will not rattle loose under heavy work. A separate black grounding lead with a male bullet connector runs out of the coil base to connect directly with the handlebar stop switch.

 

 

 

Technical Specifications

 

 

Parameter Specification
Product Brush Cutter CDI Ignition Coil Assembly
SKU 0208050
Brand SeaSummer
Armature Material Laminated Silicon Steel Core
Coil Insulation Vacuum-Poured Thermal Epoxy Resin
Ignition System Contactless Electronic CDI
Air Gap Setting 0.30 mm to 0.40 mm (0.012" to 0.016")
Compatible Engines 40-5, 44-5, CG430, CG520, 1E40F-5, 1E44F-5 (43cc / 52cc)
Lead & Terminal Silicone High-Tension Wire + Insulated Ground Lead
Delivery Time 30 Days
Packaging Cardboard packaging
   
   
   
   
   

 

Products Application

 

 

product-816-816

Mounting Hole Alignment

The slotted mounting legs match the standard M5 bolt spacing used on 40-5 and 44-5 crankcase castings. The slots allow enough lateral movement to set the clearance between the pole faces and the flywheel rim accurately before torquing down the fasteners.

product-816-816

Setting the Flywheel Air Gap

Back off the two M5 mounting bolts slightly and slide the coil outward away from the flywheel.

Rotate the flywheel by hand until the magnetic segment faces the coil pole shoes.

Slide a 0.35 mm (or 0.014") non-metallic feeler gauge across the magnetic faces.

Allow the magnetic pull to draw the coil legs tight against the gauge, then tighten both mounting bolts evenly to approximately 4.5–5.5 N·m.

Rotate the flywheel past the coil legs to pull the feeler gauge out cleanly. Check that the flywheel turns freely without rubbing against the pole faces.

product-816-816

Troubleshooting Field Failures

Replacing a failing coil restores dependable cold starting and steady full-throttle cutting in heavy brush where poor ignition causes bogging, backfiring, or mid-day thermal stalls.

Quality and Craftsmanship Details

 

product-1500-1500

 

 

 

Products Package

 

 

product-1500-1500

 

About Us

 

 

Jiaxing Norsun Trading Co., Ltd.

As an established supplier of outdoor power equipment and pneumatic components, Jiaxing Norsun Trading Co., Ltd. delivers streamlined B2B sourcing for global distributors. Backed by 200+ audited manufacturers in China, we ensure factory-direct wholesale pricing, strict incoming and outgoing inspection, and steady volume supply.

One-Stop Sourcing Hub

YOUR PROFESSIONAL ONE-STOP SOURCE
FOR 10000+ OUALITY PARTS

Direct Factory Network

200+ TRUSTED MANUFACTURING PARTNERS ACROSS CHINA

Production process

 
product-496-372
Injection MoldingPlastic & Rubber Parts
product-496-372
CNC Lathe TurningHigh-Precision OD/ID
product-496-372
CNC Machining CenterMulti-Axis Milling
-5
Precision TappingCalibrated Thread Pitch
product-496-372
Clean Assembly LineSemi-Automated Line
product-496-372
100% QC InspectionOptical & Pressure Test
product-496-372
Protective PackagingCardboard & Rust-Proof
-6
Warehouse & LogisticsFast Dispatch & Storage

Quality Assurance & Traceability: Every pneumatic component is manufactured under strict ISO quality management standards-from raw material inspection and CNC machining to thread gauge verification and 100% pressure leak testing

 

Expo experience

 

 

product-1500-2000

 

Customer Reviews

 

 

product-1500-2000

 

 

Technical Inquiries and Ordering

 

 

Q: Which engine platforms use this ignition module?

A: This coil fits standard 43cc and 52cc two-stroke utility engines with 40-5, 44-5, CG430, CG520, 1E40F-5, and 1E44F-5 crankcase layouts. It is commonly used on straight-shaft brush cutters, commercial grass trimmers, backpack clearing saws, and two-man earth augers.

Q:How do you tell if an existing coil has failed?

A:A failing ignition coil often produces a weak, yellow spark when tested against the cylinder head, or it will start the engine cold but drop spark completely after 5 to 10 minutes of running as the internal windings expand with heat.

Q: How does the grounding kill wire connect?

A:The single black wire coming from the coil body plugs directly into the engine wiring harness leading up to the handlebar throttle switch. Flicking the switch to the "OFF" position grounds the primary circuit and immediately stops the engine.

 

Q: What are the shipping package details and delivery lead time?

A:Units are individually bagged to protect the leads and packed in export Cardboard packaging. The standard production and delivery lead time is 30 Days.

 

 

 

Hot Tags: brush cutter ignition coil, China brush cutter ignition coil suppliers, Trimmer Head Sets, Fuel Tank Mixer 1L Ratio 20 1 50 1, Brush Cutter Carburetor Check Valve, 937 05145 679CC Brush Cutter Air Filter, other brush cutter parts, 799728 498231 499161 498027 4993 Carburetor

Send Inquiry