Hedge Trimmer Starter Assy

Hedge Trimmer Starter Assy

Assembly Code / SKU: 2601024 (Hedge Trimmer Recoil Starter Assembly)
Engine Compatibility: 1E32F (23cc/26cc), Echo HC-1000/1001, Shindaiwa DH212, Husqvarna 325HE3/325HE4/323HE3 Series
OEM Cross Reference: Echo A051001312, A051000941, 17720042033; Husqvarna 544071103; Shindaiwa A052000160
Housing & Internals: Impact-Resistant Polymer Shroud, Tempered Alloy Steel Recoil Spring, Braided Nylon Cord & Centrifugal Pawls
Commercial Terms: Brand: SeaSummer | Delivery Time: 30 Days | Packaging: Cardboard packaging
Send Inquiry
Add To Inquiry
Description

Jiaxing Norsun Trading Co., Ltd. is one of the leading manufacturers and suppliers of hedge trimmer starter assy in China. With abundant experience, we are committed to providing high quality customized products with low price. Welcome to wholesale bulk CE approved products in stock here and get quotation from our factory.

 

Product Overview & Operating Details

Complete Recoil Starter Assembly for Echo, Shindaiwa & Husqvarna 2-Stroke Hedge Trimmers

Direct-Replacement 4-Bolt Recoil Starter Unit with Pre-Loaded Alloy Spring, High-Density Nylon Rope & Centrifugal Starter Pawls

 
 
product-1024-1024

Engineering Profile & Working Principles

On 23cc–26cc commercial 2-stroke hedge trimmers, the recoil starter assembly endures high-frequency engine vibration and violent sudden pulling loads. Over extended landscaping service, stock starter assemblies fail in three typical ways: the braided pull rope frays and snaps, the internal flat spiral spring suffers fatigue and refuses to retract the cord, or the plastic drive pawls round off and slip over the flywheel starter cup.

Rebuilding individual starter subcomponents in the field is labor-intensive and frequently leads to spring coil unseating. Replacing the entire unit as a pre-tensioned, matched assembly restores instant, reliable engine starting and eliminates workshop downtime.

This replacement recoil starter features an impact-resistant polymer housing engineered to absorb engine vibration and resist flying hedge clippings. Inside, a tempered alloy spring steel recoil spring delivers balanced rewind tension, while a wear-resistant braided nylon cord resists surface fuzzing and oil degradation. The integrated centrifugal starter pawls extend smoothly to bite into the flywheel drive plate on the initial pull, then retract completely when the engine fires to eliminate mechanical drag.

 

 

 

Technical Specifications

 

 

Parameter Specification
Product Type 2-Stroke Hedge Trimmer Complete Recoil Starter Assembly
Part Number / SKU 2601024
Brand Identifier SeaSummer
OEM Cross References Echo: A051001312, A051000941, 17720042033 | Husqvarna: 544071103 | Shindaiwa: A052000160
Engine & Model Fitment 1E32F, 23cc, 26cc; Echo HC-1000/1001, GT/ED; Shindaiwa DH212; Husqvarna 325HE3/HE4
Housing Construction Reinforced High-Impact Engineered Polymer (Vibration & Heat Resistant)
Internal Mechanism Heavy-Duty Nylon Rope Pulley + Heat-Treated Alloy Steel Recoil Spring
Pull Cord Type High-Tensile Multi-Strand Braided Nylon Pull Rope with Ergonomic T-Handle
Flywheel Engagement Dual Centrifugal Pivot Pawls (Instant Lock-In / Clean Disengagement)
Mounting Pattern 4-Screw Symmetrical Flange (Standard T-27 Torx / Hex Fasteners)
Primary Rebuild Role Resolves Non-Retracting Rope, Snapped Starter Cord, Stripped Drive Pawls
Production Lead Time 30 Days
Master Packaging Cardboard packaging

 

Products Application

 

 

product-816-816

Pre-Assembly Dimensional Verification

Measure the 4-bolt mounting flange hole spacing with digital vernier calipers to confirm 1:1 alignment with the engine crankcase bosses.

Pull the T-handle 5–10 cm to confirm that the central starter pawls extend smoothly outward and snap back cleanly under spring return.

Inspect the outer polymer shroud for cracks or molding flash around the fastener eyelets.

product-816-816

Assembly Sequence

Disconnect the spark plug boot to prevent accidental engine firing during flywheel handling.

Remove the 4 retaining screws from the defective starter housing and clean hedge debris from the flywheel starter cup.

Position the new recoil starter onto the engine crankcase; pull the starter cord out 3–5 cm until the pawls seat squarely into the flywheel engagement dogs.

Thread in all 4 mounting screws and tighten them progressively in an alternating diagonal pattern using a T-27 Torx or hex driver. Do not over-torque to avoid cracking the polymer mounting ears.

Cycle the pull handle twice by hand to confirm smooth flywheel engagement and complete cord retraction before reconnecting the spark plug boot.

product-816-816

Operating Best Practices

Correct Pulling Technique: Before pulling hard, draw the rope out 5–10 cm until you feel the pawls firmly engage the flywheel resistance, then deliver a brisk, smooth stroke. Avoid snatching the cord from a slack position to protect pawl teeth.

Avoid Cord Over-Extension: Never pull the starter rope to its absolute mechanical end stop; guide the T-handle back to the housing rather than letting it snap back freely against the shroud.

Quality and Craftsmanship Details

 

product-1500-1500

 

 

 

Products Package

 

 

product-1500-1500

 

Practical Questions & Ordering

 

 

Q:Is this starter unit interchangeable with Echo, Shindaiwa, and Husqvarna hedge trimmers?

A: Yes. The 4-bolt mounting footprint, pawl engagement hub depth, and shroud profile directly match standard Echo HC-1000/1001, Shindaiwa DH212, and Husqvarna 325HE3/325HE4 series 2-stroke engines.

Q:Does this assembly come pre-tensioned and ready to install?

A:Yes. Each unit is fully assembled at the factory with the recoil spring pre-loaded, the braided nylon cord wound, and the starter pawls pre-installed for direct drop-in replacement.

Q: What causes recoil starter ropes to stop retracting?

A:Non-retracting ropes are caused by a fatigued, deformed, or broken flat spiral spring inside the pulley housing. Installing a complete starter assembly solves rewind failure permanently.

 

Q: What are the wholesale export packing details and standard lead times?

A:Each recoil starter assembly is packaged in an individual protective carton, then packed into master export Cardboard packaging. Standard production delivery time is 30 Days.

 

About Us

 

 

Jiaxing Norsun Trading Co., Ltd.

As an established supplier of outdoor power equipment and pneumatic components, Jiaxing Norsun Trading Co., Ltd. delivers streamlined B2B sourcing for global distributors. Backed by 200+ audited manufacturers in China, we ensure factory-direct wholesale pricing, strict incoming and outgoing inspection, and steady volume supply.

One-Stop Sourcing Hub

YOUR PROFESSIONAL ONE-STOP SOURCE
FOR 10000+ OUALITY PARTS

Direct Factory Network

200+ TRUSTED MANUFACTURING PARTNERS ACROSS CHINA

Production process

 
product-496-372
Injection MoldingPlastic & Rubber Parts
product-496-372
CNC Lathe TurningHigh-Precision OD/ID
product-496-372
CNC Machining CenterMulti-Axis Milling
-5
Precision TappingCalibrated Thread Pitch
product-496-372
Clean Assembly LineSemi-Automated Line
product-496-372
100% QC InspectionOptical & Pressure Test
product-496-372
Protective PackagingCardboard & Rust-Proof
-6
Warehouse & LogisticsFast Dispatch & Storage

Quality Assurance & Traceability: Every pneumatic component is manufactured under strict ISO quality management standards-from raw material inspection and CNC machining to thread gauge verification and 100% pressure leak testing

 

Expo experience

 

 

product-1500-2000

 

Customer Reviews

 

 

product-1500-2000

 

 

 

 

Hot Tags: hedge trimmer starter assy, China hedge trimmer starter assy suppliers

Send Inquiry