EX17/EX21 Rammer Piston Ring

EX17/EX21 Rammer Piston Ring

SKU:1702071
Application:Robin Subaru EX17 (3.5HP), EX21 (6.0–7.0HP) single-cylinder OHV petrol engines; rammer
Material:steel
Details explanation:no filing required for standard-bore installation
Operating Temp : up to 200°C
Packaging:Cardboard packaging
Delivery Time:30 Days
Send Inquiry
Add To Inquiry
Description

Jiaxing Norsun Trading Co., Ltd. is one of the leading manufacturers and suppliers of ex17/ex21 rammer piston ring in China. With abundant experience, we are committed to providing high quality customized products with low price. Welcome to wholesale bulk CE approved products in stock here and get quotation from our factory.

 

Product Introduction

EX17 / EX21 Rammer Engine Piston Ring Set - STD 67mm Compression and Oil Control Rings for Robin Subaru Rammer Compactor Engine Rebuild

Fits Robin Subaru EX17 · EX21 Single-Cylinder OHV Engines · Standard 67mm Bore · 5-Piece Set: 2× Compression Rings + Oil Control Ring Expander + 2× Side Rails - OEM Reference 277-23511-17

EX17/EX21 Rammer piston ring

Piston rings perform two interdependent functions: compression rings seal the combustion chamber from the crankcase during compression and power strokes; the oil control ring meters the oil film on the cylinder bore wall, ensuring lubrication while preventing excess oil from reaching the combustion chamber where it burns and generates carbon deposits. When rings wear through the accumulated contact cycles of continuous rammer compactor engine operation, the first measurable symptoms are reduced compression, blue exhaust smoke, and increased oil top-up frequency - addressing ring wear at this stage, before bore scoring or piston seizure, is the most cost-effective maintenance intervention available.

This five-piece ring set is manufactured to STD 67mm bore specifications for Robin Subaru EX17 and EX21 OHV engines, containing two dark gunmetal grey solid compression rings, one bronze-beaded oil control ring expander, and two thin black side rail rings - the complete ring replacement content for one standard-bore EX17 or EX21 piston. All dimensions conform to OEM Part# 277-23511-17, ensuring correct fit in the piston ring grooves and cylinder bore without filing or modification.

product-815-675
product-815-675

Technical Profiles & Materials

Dark Gunmetal Grey Steel Compression Rings for Combustion Chamber Sealing The two solid compression rings are produced from pearlitic grey cast iron or alloy steel, surface-treated to the dark gunmetal grey finish and precision-ground on the face and side surfaces to the dimensional tolerances that determine sealing performance in the ring groove. The first (top) compression ring carries the highest combustion pressure load and highest operating temperature - seated closest to the combustion chamber, it is the primary barrier against combustion gas blow-by and must maintain its face geometry and spring tension across the thousands of thermal cycles of rammer compactor engine service. The second compression ring acts as secondary combustion seal and assists oil control by scraping downward-moving oil film off the bore wall on the piston's downward stroke. Both rings are supplied at the standard end gap specification for the 67mm bore, confirming correct face pressure against the bore wall without over-tension that causes accelerated bore wear.

Bronze-Beaded Oil Control Ring Expander with Twin Side Rails for Oil Film Regulation The oil control ring assembly comprises three components: one coiled-wire bronze-beaded expander spring and two thin black steel side rails that sandwich the expander in the oil control ring groove. The expander spring provides the outward radial force that pushes the two side rails against the cylinder bore wall with sufficient pressure to scrape excess oil from the bore surface on every piston stroke - leaving a controlled thin oil film that lubricates the compression rings and piston skirt while blocking excess oil from reaching and burning in the combustion chamber. The beaded coil expander design allows the ring assembly to conform to minor bore geometry variations around the full contact circumference, maintaining consistent side rail-to-bore pressure even in bores that have developed slight taper or out-of-round from accumulated service wear. The three-piece oil control ring design is standard for the EX17/EX21 oil ring groove and maintains the OEM ring groove side clearance specification.

 

Technical Specifications

 

 

ITEM DETAILS
Type Piston Ring Set - 5-Piece (2× Compression Ring, 1× Oil Control Expander, 2× Side Rails)
Application Robin Subaru EX17 (3.5HP), EX21 (6.0–7.0HP) single-cylinder OHV petrol engines; rammer compactors, small generators, portable power equipment fitted with standard-bore EX17/EX21 engines
Code 1702071
Material Dark gunmetal grey cast iron or alloy steel compression rings; bronze-beaded coiled wire oil control expander; thin black steel side rail rings
Details explanation Bore: STD 67mm; OEM ref: Robin Part# 277-23511-17; 5-piece set per piston; 2× compression + 1× oil expander + 2× side rails; no filing required for standard-bore installation
Brand Name SeaSummer
Operating Temp up to 200°C+ at continuous rated load
Delivery Time 30 Days
Packaging Cardboard packaging

 

Products Application

 

 

product-1000-1000

Piston Ring Replacement During Compression Restoration on EX17/EX21 Rammer Engines

Small engine mechanics install this ring set when bore measurement confirms the cylinder is still within standard-size tolerance but compression testing reveals blow-by from worn ring faces - the targeted ring-only repair that restores combustion sealing without the higher cost of a complete piston and ring assembly replacement. With the piston removed and cleaned of carbon deposits from the ring grooves and crown, the worn rings are removed using a ring expander tool, and the new rings are installed one at a time onto the correct piston ring grooves in the correct orientation - compression rings with the marked side facing upward, oil rail side rails fitted into the groove before the beaded expander is positioned between them.

product-1000-1000

Ring End Gap and Side Clearance Measurement Before Installation

Before fitting the new rings onto the piston, the technician inserts each compression ring individually and squarely into the cylinder bore using the piston as a guide tool, then measures the ring end gap with a feeler gauge to confirm it falls within the OEM service specification for standard-bore EX17/EX21 engines - typically 0.15mm to 0.40mm for compression rings at room temperature. A ring end gap below the minimum specification will close completely at operating temperature, causing the ring ends to butt together and apply destructive radial force against the bore wall; a gap above the maximum allows excess combustion gas to escape through the joint on every firing stroke, reducing compression and accelerating burn-back of the ring face at the gap location.

product-1000-1000

On-Site Ring Replacement During Scheduled Rammer Compactor Engine Service at Construction Sites

Ring replacement is a standard item in the scheduled engine overhaul program for rammer compactor fleets maintained by construction companies, contractors, and plant hire companies - performed at defined engine hour intervals alongside valve inspection, cylinder bore measurement, and carburetor cleaning to maintain the compression and power output on which effective soil and granular base compaction depends. The compact five-piece ring set format allows the field service technician to carry complete ring replacement content for one engine in a small parts package as part of the site service kit - alongside a ring compressor band, feeler gauge set, and torque wrench - enabling the full ring replacement procedure at the construction site without returning the rammer to a workshop.

Quality and Craftsmanship Details

 

product-1920-1920

product-1920-1920

product-1920-1920

 

Products Package

 

 

product-1920-2560

 

About Us

 

 

Jiaxing Norsun Trading Co., Ltd.

As a premier garden machinery parts supplier, Jiaxing Norsun Trading Co., Ltd. bridges global distributors with over 100 vetted China manufacturers. We streamline your B2B supply chain through strict quality control, flexible production, and factory-direct wholesale pricing. Partner with us for reliable, high-volume sourcing of precision-engineered outdoor power equipment components.

Trusted Partnership Power

YOUR PROFESSIONAL ONE-STOP SOURCE
FOR 10000+ OUALITY PARTS

Verified Factory Excellence

BACKED BY 200+ TRUSTED FACTORY PARTNERS

Production process

 
-1
Assembling
-2
CNC Machining Center
-8
CNC Lathe
-5
Tapping Machine
-3
Tapping Machine
-7
Injection Molding Machine
-4
Inspecting
-6
Warehousing

Quality control

 
-1
-3
-4
-2

Expo experience

 

 

product-2000-2667

 

Customer Reviews

 

 

product-2000-2667

 

 

FAQ

 

 

Q: Are you an impartial industrial components dealer or a direct China water pump factors factory?

A:We are a direct, ISO9001-certified engineering water pump components manufacturing facility and precision fluid-control factor manufacture exporter primarily based in China. We function our personal cleanroom injection molding bays, computerized ultrasonic welding arrays, computerized hydraulic stress check stations, and clean-room packaging lines, passing direct-factory wholesale price financial savings straight to your element procurement margins.

Q: Can your manufacturing unit furnish full certification forms for food-contact or consuming water compliance?

A: Yes, absolutely. For food, beverage, or scientific applications, our manufacturing unit makes use of one hundred percent virgin, un-recycled polypropylene resins accompanied by means of fabric traceability certificates. We mechanically furnish B2B purchasers with complete FDA compliance documentation, NSF-grade compound declarations, and RoHS/REACH chemical protection screening sheets to make certain clean clearance thru worldwide customs.

Q: Do you provide customization picks for distinctly corrosive fluids like sturdy acids or ozone?

A: Yes, we are a thoroughly succesful OEM/ODM supplier. For aggressive chemical or ozone environments, we can improve the 12x26.5mm valve configuration in our factory: substituting the general PP housing with top class PVDF (Fluoropolymer) and changing any steel springs with Hastelloy or whole springless gravity-ball architecture, making sure final chemical resistance.

Q: How do we impervious a pattern batch to execute computerized lifecycle and burst-pressure testing?

A: We relatively inspire complete laboratory contrast earlier than logging mass grant agreements. We can ship a pattern lot of 5-10 gadgets of our inventory 12x26.5mm take a look at valves for assessment (setup costs and DHL/FedEx air freight apply). Once the factors pass by your inner lifecycle verification and a formal wholesale quantity manufacturing contract or container run is locked in, the sampling charges are a hundred percent credited returned to your industrial balance.

 

Hot Tags: ex17/ex21 rammer piston ring, China ex17/ex21 rammer piston ring suppliers

Send Inquiry