Jiaxing Norsun Trading Co., Ltd. is one of the leading manufacturers and suppliers of generator starter pulley+spring 3.5hp in China. With abundant experience, we are committed to providing high quality customized products with low price. Welcome to wholesale bulk CE approved products in stock here and get quotation from our factory.
Product Overview & Operating Details
GX120 3.5HP Utility Engine Recoil Starter Pulley & Rewind Spring Kit
Virgin Polyamide Rope Sheave with Oil-Tempered Alloy Steel Return Spring for 118cc–120cc Small Gasoline Engines

Mechanical Overview & Crank Mechanism
On small 3.5HP commercial engines, the recoil starter assembly relies on the synchronized interaction between the rope sheave and the coiled rewind spring. When the operator pulls the cord, the pulley pivots to throw the starter pawls outward into the flywheel drive cup. At the same time, the spiral spring winds tight around the center post, storing the mechanical energy required to retrieve the cord the moment the engine fires.
Continuous field use on jobsite equipment-such as vibratory plate compactors and agricultural sprayers-places intense cyclical stress on these internal components. Typical failure points on low-grade replacements include stripped center drive ramps that cause the pawls to slip under compression, cracked rope flanges, and brittle spring coils that snap after modest temperature fluctuations.
This rebuild kit pairs a precision-molded virgin nylon pulley with a factory pre-wound alloy steel return spring. The pulley features reinforced radial ribbing that resists deformation under hard pulling loads, while the smooth perimeter channel guides the cord evenly to eliminate snagging. The high-elasticity spring maintains consistent tension across wide operating temperature ranges, ensuring the pull handle returns snugly against the metal starter housing every time.
Technical Specifications
| Parameter | Specification |
|---|---|
| Product Description | Recoil Starter Rope Pulley & Rewind Spring Kit |
| SKU / Type No. | 2601082 |
| Brand Identifier | SeaSummer |
| Compatible Engine Series | GX120 (3.5HP / 118cc–120cc) Single-Cylinder 4-Stroke Gasoline Engines |
| Equipment Scope | 1kW–2kW Generators, Water Pumps, Agricultural Sprayers, Power Trowels |
| Pulley Material | Virgin Injection-Molded Polyamide with Structural Webbing |
| Spring Specification | Pre-Coiled Oil-Tempered Alloy Spring Steel (Low Tension Decay) |
| Hub Interface | Direct Fit onto Standard Starter Housing Center Pivot Post |
| Functional Role | Delivers High Cranking Torque, Eliminates Rope Snagging, Ensures Fast Rewind |
| Delivery Time | 30 Days |
| Packaging | Cardboard packaging |
Products Application

Dimensional Verification & Fit Check
Check the outer diameter and center hub bore of the nylon pulley with digital calipers. Ensure the pawl drive ramps are sharp and well-defined, and verify that the outer spring hook shows no stress fractures or deformation.

Assembly Steps
Clean the metal starter housing thoroughly to remove built-up dirt, dried grease, and rope fibers.
Seat the outer hook of the recoil spring securely into the housing retention notch, keeping the spring band flat.
Apply a light film of low-temperature machine grease to the center post and spring coils.
Lower the nylon pulley over the center post, engaging the inner spring hook with the pulley center slot.
Feed the starter cord through the housing eyelet and tie a standard figure-eight knot inside the pulley rim.
Rotate the pulley counter-clockwise 2 to 3 full turns to set the recoil preload, then allow the cord to wind smoothly into the channel. Check that the handle rests firmly against the housing.

Maintenance & Scrapping Rules
Replace Immediately: Scrape the kit if the pulley hub shows ovalization, if the rope rim is chipped, or if the spring fails to retract the cord fully.
Matched Replacement: Always replace the pulley and spring together during an overhaul to maintain balanced recoil dynamics and prevent premature wear on mating parts.
Quality and Craftsmanship Details

Products Package

About Us
As an established supplier of outdoor power equipment and pneumatic components, Jiaxing Norsun Trading Co., Ltd. delivers streamlined B2B sourcing for global distributors. Backed by 200+ audited manufacturers in China, we ensure factory-direct wholesale pricing, strict incoming and outgoing inspection, and steady volume supply.
One-Stop Sourcing Hub
YOUR PROFESSIONAL ONE-STOP SOURCE
FOR 10000+ OUALITY PARTS
Direct Factory Network
200+ TRUSTED MANUFACTURING PARTNERS ACROSS CHINA
Production process








Quality Assurance & Traceability: Every pneumatic component is manufactured under strict ISO quality management standards-from raw material inspection and CNC machining to thread gauge verification and 100% pressure leak testing
Expo experience

Customer Reviews

Practical Questions & Ordering
Q:Is this kit a direct fit for standard GX120 engines?
A:Yes. The pulley diameter, hub height, and spring hook profile match standard GX120 (3.5HP / 118cc–120cc) small gasoline engines.
Q: Does this set come with the spring pre-wound?
A:Yes. The alloy steel recoil spring is pre-coiled and held with a protective wrap to ensure safe, straightforward drop-in installation into the starter housing.
Q: Why is it important to replace the pulley and spring as a pair?
A:A worn pulley hub creates uneven spring drag, while a fatigued spring allows the rope to slap and wear the pulley rim. Replacing both as a matched kit guarantees smooth recoil action and extended durability.
Q: What are the wholesale export packing details and standard lead time?
A:Each kit is film-wrapped, packed into an individual labeled box, and consolidated in master export Cardboard packaging. The standard delivery lead time is 30 Days.
Hot Tags: generator starter pulley+spring 3.5hp, China generator starter pulley+spring 3.5hp suppliers, Generator Starter Pulley spring 3 5hp, gx120 parts, 909 Gasoline Sprayer With 139F Engine Copper Pump 90cm Gun

