Gasoline Sprayer Spring

Gasoline Sprayer Spring

Product Code / SKU: 0201012 (TU26 / 768 / CG260 Trigger Spring)
Equipment Compatibility: TU26, 768 Knapsack Power Sprayers (ASPERSORA) & CG260 26cc Brush Cutters / Grass Trimmers
Wire Metallurgy: High-Tensile Alloy Spring Steel with Stress-Relieved Heat Treatment & Anti-Corrosion Passivation
Fatigue Endurance: Rated for >100,000 Deflection Cycles with Zero Permanent Set or Preload Sag
Commercial Terms: Brand: SeaSummer | Delivery Time: 30 Days | Packaging: Cardboard packaging
Send Inquiry
Add To Inquiry
Description

Jiaxing Norsun Trading Co., Ltd. is one of the leading manufacturers and suppliers of gasoline sprayer spring in China. With abundant experience, we are committed to providing high quality customized products with low price. Welcome to wholesale bulk CE approved products in stock here and get quotation from our factory.

 

Product Overview & Operating Details

TU26 / 768 Gasoline Power Sprayer & CG260 Brush Cutter Trigger Return Spring

High-Tensile Alloy Spring Steel Wire with Corrosion-Resistant Passivation & >100,000 Cycle Fatigue Life for 26cc 2-Stroke Plant Protection & Garden Machinery

 
 
product-1024-1024

Mechanical Function & Failure Prevention

In 26cc two-stroke garden machinery-such as TU26 and 768 backpack sprayers and CG260 grass trimmers-the throttle control handle houses a small torsion spring that resets the trigger and throttle cable whenever the operator releases their grip.

Under continuous field duty, standard mild-steel wire springs degrade through stress relaxation and chemical corrosion. Repeated trigger pulls cause the wire to take a permanent set, reducing return torque. When combined with pesticide mist, fertilizer salts, and fuel wash, unpassivated springs rust, bind against the plastic handle pivot, and eventually snap. A weakened or broken spring leads to throttle cable slack, delayed shutoff, liquid chemical dribble at the spray lance, and engine runaway.

This replacement spring is cold-coiled from high-tensile alloy spring steel and batch-tempered to relieve coiling stresses. The wire retains its elastic limit through more than 100,000 full-deflection cycles without losing preload. A chemical passivation coating seals the surface against fertilizer moisture and fuel vapors, while precision-angled anchor tangs seat directly into the handle cavity and trigger lever without binding.

 

 

 

Technical Specifications

 

 

Parameter Engineering Value
Component Name 26cc Gasoline Sprayer & Brush Cutter Trigger Return Spring
Factory Part Number 0201012
Manufacturer Brand SeaSummer
Target Machinery TU26, 768 Backpack Sprayers (ASPERSORA) & CG260 26cc String Trimmers
Raw Material High-Tensile Alloy Spring Steel Wire (Stress-Relief Heat Treated)
Fatigue Life Rating >100,000 Cyclic Deflections without Yield Sag or Fatigue Fracture
Anti-Corrosion Finish Chemical Surface Passivation (Resistant to Agrochemicals, Oil & Moisture)
Anchor Interface Formed Dual Hook Tangs for Handle Casing Pocket and Trigger Pin Slot
Operational Purpose Instant Throttle Cutoff, Rapid Spray Gun Valve Reset, Cable Slack Prevention
Production Lead Time 30 Days
Export Packaging Cardboard packaging
   

 

Products Application

 

 

product-816-816

Bench Inspection & Fit Verification

Check wire diameter uniformity and coil spacing with digital calipers; ensure the active coils are free of tooling nicks or wire burrs.

Verify that both anchor tangs match the factory 90-degree and offset angles required for the handle locating slot and trigger catch.

Confirm the passivated wire finish is uniform without dark oxidation spots.

product-816-816

Handle Installation Steps

Remove the Phillips screws securing the throttle handle clam-shell casing and separate the plastic halves.

Lift out the worn spring and clean dirt, dried pesticide slurry, and debris from the internal pivot pin and cable guide.

Slide the spring body over the molded pivot boss, locking the fixed tang into the handle locating recess.

Engage the active hook into the trigger lever slot, confirming the spring coil stays centered without cocking sideways.

Apply a drop of neutral synthetic grease to the pivot boss and spring contact points to reduce plastic wear.

Reassemble the handle housing, tighten the casing screws evenly, and cycle the trigger several times by hand to confirm a crisp snap-back return.

product-816-816

Service Recommendations

Pre-Season Overhaul: Test handle trigger action before seasonal spraying. Replace sluggish or rusted springs immediately to prevent accidental chemical release.

Preserve Factory Geometry: Do not bend the anchor tangs with pliers during installation, as cold bending creates stress risers that shorten wire fatigue life.

Quality and Craftsmanship Details

 

product-1500-1500

 

 

 

Products Package

 

 

product-1500-1500

 

Practical Questions & Ordering

 

 

Q:Does this spring fit both TU26 knapsack sprayers and CG260 brush cutters?

A: Yes. Standard 26cc two-stroke garden equipment uses identical throttle handle shells and trigger pivot geometries, allowing direct interchangeability across TU26, 768, and CG260 models.

Q:How does chemical passivation protect the spring wire?

A:The surface passivation treatment converts the outer steel boundary into a corrosion-resistant barrier that stops rust from liquid fertilizers, acidic chemical mists, and washdown water.

Q: What are the primary symptoms of a failing trigger spring?

A:Symptoms include a loose or spongy trigger, delayed engine deceleration after releasing the throttle, and chemical dripping from the spray gun nozzle when closing the lance valve.

 

Q: What are the standard wholesale export packing terms and delivery times?

A:Each spring is mounted on an individual display blister card and packed into master export Cardboard packaging. Production lead time is 30 Days.

 

About Us

 

 

Jiaxing Norsun Trading Co., Ltd.

As an established supplier of outdoor power equipment and pneumatic components, Jiaxing Norsun Trading Co., Ltd. delivers streamlined B2B sourcing for global distributors. Backed by 200+ audited manufacturers in China, we ensure factory-direct wholesale pricing, strict incoming and outgoing inspection, and steady volume supply.

One-Stop Sourcing Hub

YOUR PROFESSIONAL ONE-STOP SOURCE
FOR 10000+ OUALITY PARTS

Direct Factory Network

200+ TRUSTED MANUFACTURING PARTNERS ACROSS CHINA

Production process

 
product-496-372
Injection MoldingPlastic & Rubber Parts
product-496-372
CNC Lathe TurningHigh-Precision OD/ID
product-496-372
CNC Machining CenterMulti-Axis Milling
-5
Precision TappingCalibrated Thread Pitch
product-496-372
Clean Assembly LineSemi-Automated Line
product-496-372
100% QC InspectionOptical & Pressure Test
product-496-372
Protective PackagingCardboard & Rust-Proof
-6
Warehouse & LogisticsFast Dispatch & Storage

Quality Assurance & Traceability: Every pneumatic component is manufactured under strict ISO quality management standards-from raw material inspection and CNC machining to thread gauge verification and 100% pressure leak testing

 

Expo experience

 

 

product-1500-2000

 

Customer Reviews

 

 

product-1500-2000

 

Hot Tags: gasoline sprayer spring, China gasoline sprayer spring suppliers, KI DAVR 95S3 AVR, BS21 18 Water Seal, gasoline generator parts, D 8011 Throttle Cable, Generator European Plug, Agriculture Sprayer Flexible Joint

Send Inquiry