Hey there! I'm an expert in the field of trimmer line trimmer heads, and I run a trimmer line trimmer head supply business. Today, I'm gonna walk you through the process of installing a trimmer line trimmer head on a curved shaft trimmer. It might seem a bit tricky at first, but with the right steps and a bit of patience, you'll have it up and running in no time.
What You'll Need
Before we start, let's gather all the stuff you'll need. First off, you'll need a trimmer line trimmer head. We offer a great T25 Brush Cutter Trimmer Head that's high - quality and durable. You'll also need the appropriate trimmer line. We have two popular options: the 2.7mmX15m Trimmer Line (0.105”) Dual Round and the 2.4mmX15m Trimmer Line Dual Round. Choose the one that suits your needs.
Other tools you'll need include a pair of pliers, a screwdriver (usually a Phillips - head), and safety gear like gloves and safety glasses. Safety first, folks!
Step 1: Prepare Your Trimmer
The first thing you gotta do is make sure your curved shaft trimmer is turned off and the spark plug wire is disconnected. This is super important to avoid any accidental starts while you're working on it. You don't want to get hurt, right?
Once you've done that, place the trimmer on a flat and stable surface. This will make it easier for you to work on the trimmer head installation.
Step 2: Remove the Old Trimmer Head
Now, it's time to get rid of the old trimmer head. Most curved shaft trimmers have a locking mechanism that holds the trimmer head in place. Look for a small screw or a locking tab near the base of the trimmer head.
If it's a screw, use your screwdriver to loosen it. If it's a locking tab, you might need to use your pliers to gently pry it open. Once the locking mechanism is undone, you can carefully pull the old trimmer head off the shaft. Be careful not to lose any small parts that might come off with the head.
Step 3: Inspect the Shaft
After removing the old trimmer head, take a good look at the shaft. Check for any signs of damage, like cracks or bends. If you notice any problems, you might need to get the shaft repaired or replaced before you install the new trimmer head.
Also, clean the shaft to remove any dirt, debris, or old trimmer line that might be stuck to it. You can use a clean cloth or a small brush to do this. A clean shaft will ensure a proper fit for the new trimmer head.
Step 4: Prepare the New Trimmer Head
Before you install the new trimmer head, you need to prepare it. Start by threading the trimmer line. Take your chosen trimmer line and find the line holes on the new trimmer head.
Most trimmer heads have two holes for the dual - line setup. Insert one end of the trimmer line into one hole and then thread it through the head according to the instructions on the package. Usually, you'll need to wind the line around a spool inside the head. Make sure you wind it tightly and evenly to prevent any tangles.
Leave about 6 - 8 inches of the line sticking out of the head after you've wound it. This will be the cutting part of the line.
Step 5: Install the New Trimmer Head
Now that the new trimmer head is ready, it's time to put it on the shaft. Line up the holes in the new trimmer head with the corresponding holes on the shaft. Make sure it fits snugly onto the shaft.
Once it's in place, re - engage the locking mechanism. If it was a screw, tighten it with your screwdriver. If it was a locking tab, use your pliers to close it securely.
Step 6: Test the Installation
After installing the new trimmer head, it's a good idea to do a quick test. Reconnect the spark plug wire and turn on the trimmer. Let it run for a few seconds and listen for any strange noises. If everything sounds normal, you're good to go.
However, if you hear any rattling or the trimmer head doesn't seem to be spinning smoothly, turn off the trimmer immediately and check the installation again. There might be something wrong with the fit or the way the line is threaded.
Step 7: Fine - Tuning
If the trimmer head is spinning but the line isn't feeding out properly, you might need to do some fine - tuning. Some trimmer heads have an adjustment mechanism that allows you to control the line feed.


Refer to the user manual of your trimmer head to find out how to adjust it. You might need to turn a small screw or a knob to increase or decrease the line feed.
Why Choose Our Trimmer Line Trimmer Heads
At our supply business, we take pride in offering top - notch trimmer line trimmer heads. Our products are made from high - quality materials that can withstand tough working conditions. Whether you're a professional landscaper or a homeowner looking to keep your yard in shape, our trimmer heads are a great choice.
We also offer a wide range of trimmer lines to suit different needs. Our 2.7mmX15m Trimmer Line (0.105”) Dual Round is great for thick and tough grass, while the 2.4mmX15m Trimmer Line Dual Round is perfect for lighter trimming jobs.
Contact Us for Purchasing
If you're interested in our trimmer line trimmer heads or trimmer lines, we'd love to hear from you. Whether you're a small - scale buyer or a large - scale distributor, we can offer you competitive prices and excellent customer service. Reach out to us to start a purchasing discussion, and let's find the best trimmer solutions for you.
References
- Manufacturer's user manuals for curved shaft trimmers and trimmer line trimmer heads.
- Personal experience and expertise in the trimmer supply industry.

