Jiaxing Norsun Trading Co., Ltd. is one of the leading manufacturers and suppliers of generator 168f piston pin in China. With abundant experience, we are committed to providing high quality customized products with low price. Welcome to wholesale bulk CE approved products in stock here and get quotation from our factory.
Product Overview & Operating Details
168F / GX160 / GX200 Gasoline Engine Precision Forged Piston Wrist Pin (18×54mm)
Case-Hardened Alloy Steel Hollow Wrist Pin with Superfinished Mirror Polish & HRC 58–62 Surface Hardness for 5.5HP–6.5HP Utility Generators

Mechanical Role & Reciprocating Load Dynamics
In single-cylinder 4-stroke utility engines, the piston pin (wrist pin) serves as the primary mechanical link transmitting high-pressure combustion explosive force from the piston crown to the connecting rod and crankshaft assembly. Operating at engine speeds up to 3600 RPM, the pin endures severe cyclical bending moments and high-frequency directional reversal loads.
If a soft or low-precision wrist pin is installed, intense combustion pressures cause micro-flexing and oval deformation. This pin distortion pinches the connecting rod small-end bushing, accelerates boss wear, generates loud mechanical knocking, and risks catastrophic piston boss fracture or cylinder wall scoring.
This precision 18×54mm wrist pin is hot-forged from high-grade alloy structural steel, delivering high core ductility and bending fatigue strength. The outer journal undergoes carburizing heat treatment to achieve HRC 58–62 surface hardness, followed by mirror-grade superfinishing (0 to -0.005 mm micro-tolerance). The internal hollow bore reduces reciprocating inertia mass on the crankshaft, while precision-chamfered ends protect wire circlip retention under continuous full-load generator operation.
Technical Specifications
| Parameter | Specification |
|---|---|
| Product Description | 4-Stroke Small Engine Precision Forged Piston Wrist Pin |
| SKU / Part Code | 1601165 |
| Type Specification | 168F (18×54 mm Standard Size) |
| Brand Identifier | SeaSummer |
| Compatible Engine Series | Honda GX160 (5.5HP), GX200 (6.5HP) & 168F, 170F Single-Cylinder OHV Engines |
| Machinery Applications | 2.0kW to 3.5kW Generator Sets, High-Pressure Washers, Centrifugal Pumps, Tillers |
| Nominal Outer Diameter (OD) | Φ18 mm (Precision Tolerance: 0 to -0.005 mm) |
| Nominal Overall Length | 54 mm (Direct Fit for 68 mm Bore Piston Boss Spacing) |
| Internal Geometry | Straight Cylindrical Hollow Core (Lightweight Inertia-Reduction Profile) |
| Material & Heat Treatment | Precision Forged Alloy Steel with Carburized Case Hardening |
| Surface Hardness & Finish | HRC 58–62 Case Hardness; Superfinished Low-Friction Ground Mirror Surface |
| Operational Function | Transmits Peak Combustion Thrust, Resists Bending Flex, Eliminates Pin Knock |
| Production Lead Time | 30 Days |
| Master Packaging | Cardboard packaging |
Products Application

Pre-Assembly Dimensional Verification
Measure the outer diameter with an outside digital micrometer across both ends and the center journal to confirm an 18.0 mm nominal dimension within 0 to -0.005 mm tolerance. Inspect the outer surface under bright lighting to ensure zero scratches, burrs, or grinding chatter marks. Verify that end chamfers are smooth and free of sharp edges.

Assembly Sequence
Install one 18mm spring steel wire circlip into the piston boss groove, ensuring it is 100% seated with the gap oriented away from the piston thrust axis.
Heat the aluminum piston evenly to approximately 70°C–80°C in an oil bath or thermal heater to gently expand the pin bosses.
Coat the wrist pin outer surface and connecting rod small-end bushing with clean engine assembly oil.
Align the connecting rod small end between the heated piston bosses and slide the 18×54mm pin smoothly through by hand. Never drive the pin with a steel hammer.
Install the second circlip into the opposite boss groove. Visually verify that both circlips are fully locked into their retaining recesses.
Pivot the connecting rod by hand to confirm smooth, unrestricted rotational clearance without axial binding.

Service & Operating Best Practices
Mandatory Circlip Replacement: Always install new 18mm wire circlips during piston assembly; never reuse old clips that have suffered plastic deformation.
Pre-Lubrication Requirement: Ensure the pin and rod bushing are coated with clean engine oil before assembly to establish hydrodynamic lubrication on the very first engine crank.
Quality and Craftsmanship Details

Products Package

Practical Questions & Ordering
Q:Is this 18×54mm piston pin a direct fit for Honda GX160 and 168F engines?
A: Yes. The 18 mm outer diameter and 54 mm length match standard factory dimensions for 168F, 170F, GX160, and GX200 single-cylinder 4-stroke gasoline engines.
Q:Why is a hollow core design used instead of a solid steel pin?
A:The hollow core removes non-structural central mass, significantly reducing reciprocating inertia loads on the crankshaft and main bearings at 3600 RPM while maintaining high bending strength.
Q:What causes wrist pin knocking in small engines?
A:Pin knocking occurs when excessive clearance develops from a worn, undersized, or distorted pin. Installing a precision-ground, case-hardened HRC 58–62 pin restores exact oil clearance and eliminates piston rattle.
Q: What are the wholesale export packing details and standard lead times?
A:Each piston pin is protected in anti-corrosion oil wrap and boxed, then packed into master export Cardboard packaging. Standard production delivery time is 30 Days.
About Us
As an established supplier of outdoor power equipment and pneumatic components, Jiaxing Norsun Trading Co., Ltd. delivers streamlined B2B sourcing for global distributors. Backed by 200+ audited manufacturers in China, we ensure factory-direct wholesale pricing, strict incoming and outgoing inspection, and steady volume supply.
One-Stop Sourcing Hub
YOUR PROFESSIONAL ONE-STOP SOURCE
FOR 10000+ OUALITY PARTS
Direct Factory Network
200+ TRUSTED MANUFACTURING PARTNERS ACROSS CHINA
Production process








Quality Assurance & Traceability: Every pneumatic component is manufactured under strict ISO quality management standards-from raw material inspection and CNC machining to thread gauge verification and 100% pressure leak testing
Expo experience

Customer Reviews

Hot Tags: generator 168f piston pin, China generator 168f piston pin suppliers, KI DAVR 95S3 AVR, BS21 18 Water Seal, gasoline generator parts, D 8011 Throttle Cable, Generator European Plug, Agriculture Sprayer Flexible Joint

